Chainsaw Tips to extend the life of your chainsaw

Our Reader Score
[Total: 1 Average: 5]

Tips & TricksTree removal services, lumberjacks and loggers all know that you must keep your chainsaws in good working condition. If you do not maintain your equipment you will not be productive when felling trees. You should use the following chainsaw tips to extend the life of your chainsaw.

Chainsaw tips – General care maintenance tips

  1. A person should frequently check the bar oil level on your device. Cutters should make this check right before you use your blades.
  2. The blades must be kept sharp at all times. This will allow for more efficiency while slicing through trees. Sharp blades will also prevent the chainsaw from pushing back while in use and it will help to protect the chainsaw operator.
  3. Chainsaw operators should remove dust and wood chips from your saw after each use.

Chainsaw tips – How To Sharpen a Chainsaw

Katzco -Chainsaw Sharpener Filing Kit 8 Pc Set, Comes w/ 3/8″ Handle, 6″ Flat File, Depth-Gauge Tool, Filing Guide, Tool Pouch, 3 Round File,(5/32″-3/8″ LP Pitch)(3/16″-.325″ Pitch)(7/32″-3/8″ Pitch)

Cutters can use a filing device to sharpen the blades on your units. Sharp blades help to reduce stress on the saw and the operator. The following steps should be taken when sharpening blades.

  • Place the unit in a vice so that it does not move while sharpening the blades.
  • Make sure the brake has been engaged.
  • Start sharpening the teeth first. Position the filing device on the blades so that the arrows point toward the buzz nose.
  • Operators should file at a right angle toward the rollers.
  • Every other tooth on the saw should be filed. Use a smooth and even motion to perform this task.
  • Now the blades around to the opposite direction.
  • Perform the same steps on the opposite side of the blade.

File the depth gauge

Cutters should grind the depth gauge on your motor axes about every third time you sharpen your teeth. Depth gauges are located between the teeth. The following steps should be taken when filing the depth gauge:

  • Put the gauge over the top of the depth gauge.
  • Choose the “hard” or “soft” setting depending on the type of wooden material that is typically cut with the saw.
  • Grind the depth gauge until the filing unit comes into con\tact with the gauge.

Chainsaw tips – How to change a chain and bar

Husqvarna 531300440 20-Inch FT280-72 Chain Saw Bar, 3/8-Inch by .050-Inch

Eventually, the longest part of the tooth will wear down. Once the blade has been worn down to less than 4 mm, the chain will have to be replaced.

  1. The bar must be removed and a new chain must be put into place.
  2. The next step is to adjust the tension on the chain. Make sure that the unit is not too lose otherwise it will come off of the bar. Operators should ensure that the blades are not too tight because this will wear down the bar.
  3. The chain should have enough room to be pulled up about 1 cm from the bar on the track. It should easy to rotate the chain unit with your hand.

Chainsaw tips – How to clean up a chainsaw

Cleaning a motor axe is an important part of maintenance. Cutters should make sure that you are paying attention to the following things:

  • Locate and remove the clutch cover.
  • Wipe down the chain brake band.
  • Occasionally clean out the chain bar by using a thin tool to scoop out any materials from inside of the track.
  • Locate and then remove the cylinder cover.
  • Wash out the air filter.
  • Wipe the cooling fins and air intake if materials are present between the slots.
  • Periodically check the flywheel fins to ensure that nothing is blocking the air from cooling the engine.

Chainsaw tips – Other Important checkpoints

Chainsaw operators should inspect your machines to figure out if you have any mechanical issues.You should periodically check the following functions:

  • Put the saw on a stable surface.
  • Release the brake and squeeze the throttle.
  • Activate the brake by moving the bar. Do not release the handle, Taking this action should make the chain stop rotating.
  • Check the throttle and the chain’s catcher and lubrication.
  • Inspect the chain drive wheel and make sure it is not worn out.
  • Tighten up parts on the saw that are loose.

View more helpful CHAINSAW TIPs here

 

 

A power saw can be a considerable purchase. That’s why the few minutes that you spend on reading power saw reviews is time well spent. Not only can you save money but you can also avoid headaches by purchasing only the right tool for your need. Here, I share my personal experiences and honest reviews about power saws to help you sense what it is like to work before you actually purchase one. My experiences and opinions act as a litmus test for first time users and for those who want to upgrade their power saws. Wish to help you identify the most significant factors that should influence your decision when buying the best power saws.

We will be happy to hear your thoughts

Leave a reply