How To Operate an MK Tile Saw and Cutter

Our Reader Score
[Total: 2 Average: 5]
Basically, an MK wet saw can be used for cutting quarry tile, ceramic tile, stale and marble. You can always find this type of saw for rent in tile stores and at home remodel places. They are often called wet saws. This is because a source of water is usually pumped over the blade to keep it the MK tile saw from overheating.

MK-370EXP 1-1/4 HP 7-Inch Wet Cutting Tile Saw

MK-370EXP 1-1/4 HP 7-Inch Wet Cutting Tile Saw

4 Steps To Use an MK Tile Saw Easily

 MK tile saws are used instead of the local tile cutters for a gamut of reasons. They usually cut tiles that are bigger in size than the traditional cutter. MK tile saws can usually design cuts on a diagonal that cannot fit a local cutter. This type of saw can as well cut smaller than the local cutter can handle.

Is your quest on how to operate an MK tile saw and cutter? Have you been looking for the best ways of operating MK wet saws? Reading through the rest part of this article will help you greatly on how to operate an MK tile saw and cutter easily.

Step 1: 

The first step to take is by setting up the base of the device at a comfortable height. You will also have to do the setting in an environment where water thrown off won’t create a problem. This will enable your set up process to work effectively without any stress.

Step 2:

Next on the list is to position the water pan on the base. Go ahead to fill a bucket or container with water and ensure to position the pump in the tank. Ensure that the rubber hose is attached properly to the saw housing and the pump. Go ahead to turn the MK saw on and ensure the water is spraying on the blade. Finally, you can turn off the saw.

Step 3:

The sliding tray should be properly positioned on the rails over the pan. The trail usually comes with measurements on it where you position the tile and make slide into the spinning blade. Now, you can ensure to check the height of the blade. It is important to make sure the slot in the tray slide beneath the blade without binding, but the saw should extend below the surface of the tray.

Step 4:

At this juncture, mark and measure the tiles and position it on the tray so that the side or measurement of the cut parallel with the blade. Go ahead to slide it into the blade and ensure that the cut will be the same where you want the process to occur. Turn on the MK wet saw by pulling the tray backward. Now, ensure to slide the saw gently forward into the blade.

Allow the blade of the saw to draw the tile into while applying low pressure. Allow the MK wet saw blade to cut all the way through the edge of the tile. This should be done prior to turning off the blade.

Conclusion:

You can always apply gentle, but steady force to the tiles as the device blade cuts through it. The idea of working too fast can enable the tile to crumble or break. You can always contact someone at the store to display the process of how to set up the device for use. Normally, it is easy to set up, but can take a little getting used to.

It is important to know that the MK saw uses a lot of water. Ensure to always position the pump in a large container or bucket of water. This will make it fill and clog the pump with sediment. The truth is that wet saws often use a lot of water.

The shields or protectors around the blade try to maintain most of it in the pan, but some can be thrown away outside and make a mess. You can ensure to set up the saw in a place where cleaning can be done easily. If you push the tile into the blade, ensure to bind it up effectively. If it is not properly done, try to cut the power instantly.

Just as will do with any power saw tool, ensure to take adequate care around the blade. The blade is usually made to grind through a hard surface, but can cause abrasions and burns.

A power saw can be a considerable purchase. That’s why the few minutes that you spend on reading power saw reviews is time well spent. Not only can you save money but you can also avoid headaches by purchasing only the right tool for your need. Here, I share my personal experiences and honest reviews about power saws to help you sense what it is like to work before you actually purchase one. My experiences and opinions act as a litmus test for first time users and for those who want to upgrade their power saws. Wish to help you identify the most significant factors that should influence your decision when buying the best power saws.

We will be happy to hear your thoughts

Leave a reply